8 Inch Intelligent LCD Module DMG80600T080_02W(Industrial Grade)

Video Specification Hardware and interface description User interface 8Pin_2.0mm socket for power supply and serial communication. Download rate(typical value): 12KByte/s Flash 16 MBytes NOR Flash, for fonts, pictures and audio files. Rewrite cycle: over 100,000 times Expand Flash pads Three expansion slots are available, supporting expansion of NOR Flash and NAND Flash. The maximum expansion for NOR Flash is up to 64Mbytes. When combining NOR Flash and NAND Flash, the maximum expansion is up to 48Mbytes (using two expansion slots) + 512Mbytes.When expanding Flash, components such as decoders and capacitors need to be soldered. Please consult the corresponding salesperson for relevant customization (Located inside the shielding cover) Buzzer 3V passive buzzer RTC Super-capacitor supplies power to RTC, accuracy: ±20ppm @25℃. Can maintain normal operation for 7 days after power-off. Reserved button cell power supply compatible circuit. SD card slot Supports downloading of all files (user UI files, CFG files, underlying kernel firmware), displays download statistics on the screen, download rate: 4 Mb/s. When downloading files, the SD card needs to be formatted in FAT32 format, with a recommended allocation unit size of 4096 Reserved module interface Supports soldering of WI-FI module and USB download module. WI-FI module model: WI-FI-10; USB module models: HDL702, HDL703 PGT05 interface Used for reprogramming the underlying DGUS firmware Display Parameters LCD Type TN process TFT LCD screen Viewing Angle Normal viewing angle, 70°/70°/50°/70° (L/R/U/D) Resolution 800×600 pixels (support 0°/90°/180°/270°) Color 16.7M color (24-bit 8R8G8B) Active Area (A.A.) 162.00mm (W)×121.50mm (H) Interface RGB Backlight Mode LED Backlight Service Life >30000 hours (Time of the brightness decaying to 50%on the condition of continuous working with the maximum brightness) Brightness DMG80600T080_02WTC: 300nit DMG80600T080_02WTR: 250nit DMG80600T080_02WN: 350nit Brightness Control 0~100 grade (When the brightness is adjusted to 1%~30%of the maximum brightness, flickering may occur and is not recommended to use in this range) Note: You can use dynamic screen saver wallpapers to avoid afterimages caused by fixed page display for a long time. Touch Parameters Type CTP (Capacitive touch panel) Interface I²C Structure Single point touch and support continuous sliding touch Touch Mode Support point touch and drag Surface Hardness 6H Light Transmittance >85% Life Over 1,000,000 times touch    Type RTP (Resistive touch panel) Structure ITO film + ITO glass Touch Mode Single point touch and support continuous sliding touch Surface Hardness 3H Light Transmittance >80% Life Over 1,000,000 times touch Serial Interface Parameters Mode UART2: ON=TTL/CMOS; OFF=RS232 UART4: ON=TTL/CMOS; OFF=RS232(Only available after OS configuration) Voltage Level Test Condition Min Typ Max Unit Output 1, Iout = -4mA 4.78 5.0 - V Output 0, Iout = 4mA - - 0.4 V Input 1 2.5 5.0 - V Input 0 - - 1.0 V Baud Rate 3150~3225600bps, typical value of 115200bps Data Format UART2: N81 UART4: N81/E81/O81/N82 , 4 modes (OS configuration) Interface Cable 8Pin_2.0mm Electrical specifications Rated Power <5W Operating Voltage 6~36V, typical value of 12V Operating Current 280~320mA VCC=12V, max backlight 100mA VCC=12V, backlight off Recommended power supply: 12V 1A DC Operating environment Operating Temperature -20℃~70℃ (12V @ 60% RH) Storage Temperature -30℃~80℃ Conformal Coating Yes Operating Humidity 10%~90%RH, typical value of 60% RH Application